RadiSys ATCA-5400 RTM Dokumentacja Pobierz pdf (Strona 165)

C and SMBus map

165

PCA9555 (AMC PCIe and RTM

PCIe0)

Slave IOH SMBus 41h 40h

PCA9555 (RTM PCIe1) Slave IOH SMBus 43h 42h

The three geographical pins GA[2:0] are used to assign to IPMB-L address of the AMC. G=Logic Ground,

U=Unconnected, P=Pulled up to P3V3 Management Power.

The IPMB-L address of the RTM is assigned in the firmware.

Table 55. I

C and SMBus device addresses (continued)

Device Master / slave Bus # Read address Write address

1 2 ... 160 161 162 163 164 165 166 167 168 169 170 ... 173 174

PROMENTUM® 1
Release history 2
TABLE OF CONTENTS 3
Table of Contents 4
About this manual 7
What’s new in this manual 7
Notational conventions 8
Related manuals 9
Related Documents 10
1PRODUCT OVERVIEW 13
Block diagram 14
I/O capabilities 15
Hardware management 16
Supported DIMM combinations 17
Electrostatic discharge 18
DIMM socket 19
Ejector latch 19
Testing installed memory 20
Installing Memory Modules 22
3LEDS AND EXTERNAL INTERFACES 23
LEDs and External Interfaces 24
Front panel LEDs 26
Front panel connectors 26
Reset button 27
Other physical interfaces 29
4COMPONENTS AND SUBSYSTEMS 31
Integrated memory controller 32
Memory and storage devices 33
DDR3 SDRAM 34
Redundant boot flash 34
Redundant user flash 35
Components and Subsystems 36
USB controller 37
SATA controller 37
LPC bridge 37
Real-time clock 38
Super I/O chip 39
TPM chip 39
SAS and SATA 39
Multiplexer 40
Base Interface 41
Fabric interface 41
10GbE Fabric Configuration 43
GbE Fabric Configuration 43
BackplaneCPM 46
C (Bus 3) 47
CPU complex FPGA 48
5HARDWARE MANAGEMENT 49
IPMC description 50
IPMC FPGA 51
IPMC SEEPROM 51
IPMC system event log 51
Redundant firmware images 52
Summary of IPMC controls 53
Overview of sensor management 54
CPM resets 55
Reset source monitor 56
Watchdog timers 57
IPMC watchdog 58
BMC watchdog 58
E-Key control of interfaces 59
Hardware Management 60
IPMI-over-LAN 62
Serial-over-LAN 65
Establishing a SOL session 69
BIOS setup menus 71
System BIOS 72
Installing bioscli2 73
Creating a custom BIOS image 74
Corr.Error 76
Threshold 76
NMI/Reset] 77
Accessing the SEL 78
SEL event codes 78
Critical 84
Slide lock toward 85
Locking latch 85
ARNING! 86
Overview of firmware updates 87
RPMs required for updates 88
General troubleshooting tips 89
Environmental specifications 91
Safety specifications 92
Mechanical specifications 92
Power consumption 94
General assumptions 95
General notes 95
Specifications 96
Supported IPMI commands 97
Results completion codes 99
OEM command descriptions 100
Switch Active Boot Flash 101
Get Active Boot Flash 101
RTM Reset Button 102
Set Payload Status 102
Managed sensors 104
List of sensors 105
= watchdog 114
As - - - N/A 03h 119
If the boot error occurred 121
Power Cycle 122
IPMC Redundancy State 122
Failover Start 122
Failover Complete 122
OEM sensor details 123
Temperature sensor details 124
Sensor alarm troubleshooting 125
Temperature sensor locations 139
Front panel interfaces 141
Backplane interfaces 142
Zone 1 P10 connector pinout 143
Zone 2 J20 connector pinout 144
Zone 2 J23 connector pinout 145
RTM interface pinout 146
AMC connector pinout 147
Jumper settings 152
FRU information areas used 153
Multirecord area records used 153
CPM and FRU device IDs 154
PCI bus device map 155
Low-Level Hardware Map 156
Interrupts 158
APIC interrupt mapping 159
PIC interrupt mapping 160
C and SMBus map 163
Commands 167
Advanced commands 168
Troubleshooting 169
BIOSCLI2 commands 170
Implement iSCSI boot 171
Configure iSCSI Boot 172
Install support packages 174

Komentarze do niniejszej Instrukcji

Brak uwag

RadiSys ATCA-5400 RTM Dokumentacja Strona 165

Komentarze do niniejszej Instrukcji